Klipper config

This commit is contained in:
Nathan McCarty 2023-10-07 23:44:31 -04:00
parent 5bb4903f24
commit 6b81fd582b
Signed by: thatonelutenist
SSH Key Fingerprint: SHA256:hwQEcmak9E6sdU9bXc98RHw/Xd1AhpB5HZT7ZSVJkRM
2 changed files with 137 additions and 0 deletions

View File

@ -73,6 +73,7 @@
services.klipper = {
package = inputs.nixpkgs-unstable.legacyPackages.${pkgs.system}.klipper;
enable = true;
configFile = ./klipper/printer.cfg;
};
services.moonraker = { enable = true; };
services.mainsail = {

View File

@ -0,0 +1,136 @@
# This file contains pin mappings for the stock 2021 Creality Ender 3
# S1 & S1 Pro. To use this config, check the STM32 Chip on the
# Mainboard, during "make menuconfig" select accordingly either the
# STM32F103 with "28KiB bootloader" or the STM32F401 with
# "64KiB bootloader" and serial (on USART1 PA10/PA9) for both.
# For a direct serial connection, in "make menuconfig" select
# "Enable extra low-level configuration options" and Serial
# (on USART2 PA3/PA2), which is on the 10 pin IDC cable used
# for the LCD module as follows: 3: Tx, 4: Rx, 9: GND, 10: VCC
# Flash this firmware by copying "out/klipper.bin" to a SD card and
# turning on the printer with the card inserted. The filename
# must be changed to "firmware.bin"
# With STM32F401, you might need to put "firmware.bin" in a
# folder on the SD card called "STM32F4_UPDATE" in order to flash.
# See docs/Config_Reference.md for a description of parameters.
[stepper_x]
step_pin: PC2
dir_pin: PB9
enable_pin: !PC3
microsteps: 16
rotation_distance: 40
endstop_pin: !PA5
position_endstop: -10
position_max: 235
position_min: -15
homing_speed: 50
[stepper_y]
step_pin: PB8
dir_pin: PB7
enable_pin: !PC3
microsteps: 16
rotation_distance: 40
endstop_pin: !PA6
position_endstop: -8
position_max: 238
position_min: -13
homing_speed: 50
[stepper_z]
step_pin: PB6
dir_pin: !PB5
enable_pin: !PC3
microsteps: 16
rotation_distance: 8
endstop_pin: probe:z_virtual_endstop
position_max: 270
position_min: -4
[extruder]
step_pin: PB4
dir_pin: PB3
enable_pin: !PC3
microsteps: 16
gear_ratio: 42:12
rotation_distance: 26.359
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PA1
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC5
control: pid
pid_Kp: 23.561
pid_Ki: 1.208
pid_Kd: 114.859
min_temp: 0
max_temp: 260 # Set to 300 for S1 Pro
[heater_bed]
heater_pin: PA7
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC4
control: pid
pid_Kp: 71.867
pid_Ki: 1.536
pid_Kd: 840.843
min_temp: 0
max_temp: 100 # Set to 110 for S1 Pro
[heater_fan hotend_fan]
pin: PC0
[fan]
pin: PA0
[mcu]
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
restart_method: command
[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 2000
max_z_velocity: 5
max_z_accel: 100
[bltouch]
sensor_pin: ^PC14
control_pin: PC13
x_offset: -31.8
y_offset: -40.5
z_offset: 0
probe_with_touch_mode: true
stow_on_each_sample: false
[bed_mesh]
speed: 120
mesh_min: 10, 10
mesh_max: 200, 194
probe_count: 4,4
algorithm: bicubic
[safe_z_home]
home_xy_position: 147, 154
speed: 75
z_hop: 10
z_hop_speed: 5
[filament_switch_sensor e0_sensor]
switch_pin: !PC15
pause_on_runout: true
runout_gcode: PAUSE
[pause_resume]
recover_velocity: 25
[bed_screws]
screw1: 20, 29
screw2: 195, 29
screw3: 195, 198
screw4: 20, 198