Klipper config

machines/universe/configuration.nix

@@ -73,6 +73,7 @@
   services.klipper = {
     package = inputs.nixpkgs-unstable.legacyPackages.${pkgs.system}.klipper;
     enable = true;
+    configFile = ./klipper/printer.cfg;
   };
   services.moonraker = { enable = true; };
   services.mainsail = {

machines/universe/klipper/printer.cfg

@@ -0,0 +1,136 @@
+# This file contains pin mappings for the stock 2021 Creality Ender 3
+# S1 & S1 Pro. To use this config, check the STM32 Chip on the
+# Mainboard, during "make menuconfig" select accordingly either the
+# STM32F103 with "28KiB bootloader" or the STM32F401 with
+# "64KiB bootloader" and serial (on USART1 PA10/PA9) for both.
+
+# For a direct serial connection, in "make menuconfig" select
+# "Enable extra low-level configuration options" and  Serial
+# (on USART2 PA3/PA2), which is on the 10 pin IDC cable used
+# for the LCD module as follows: 3: Tx, 4: Rx, 9: GND, 10: VCC
+
+# Flash this firmware by copying "out/klipper.bin" to a SD card and
+# turning on the printer with the card inserted. The filename
+# must be changed to "firmware.bin"
+
+# With STM32F401, you might need to put "firmware.bin" in a
+# folder on the SD card called "STM32F4_UPDATE" in order to flash.
+
+# See docs/Config_Reference.md for a description of parameters.
+
+[stepper_x]
+step_pin: PC2
+dir_pin: PB9
+enable_pin: !PC3
+microsteps: 16
+rotation_distance: 40
+endstop_pin: !PA5
+position_endstop: -10
+position_max: 235
+position_min: -15
+homing_speed: 50
+
+[stepper_y]
+step_pin: PB8
+dir_pin: PB7
+enable_pin: !PC3
+microsteps: 16
+rotation_distance: 40
+endstop_pin: !PA6
+position_endstop: -8
+position_max: 238
+position_min: -13
+homing_speed: 50
+
+[stepper_z]
+step_pin: PB6
+dir_pin: !PB5
+enable_pin: !PC3
+microsteps: 16
+rotation_distance: 8
+endstop_pin: probe:z_virtual_endstop
+position_max: 270
+position_min: -4
+
+[extruder]
+step_pin: PB4
+dir_pin: PB3
+enable_pin: !PC3
+microsteps: 16
+gear_ratio: 42:12
+rotation_distance: 26.359
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PA1
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC5
+control: pid
+pid_Kp: 23.561
+pid_Ki: 1.208
+pid_Kd: 114.859
+min_temp: 0
+max_temp: 260 # Set to 300 for S1 Pro
+
+[heater_bed]
+heater_pin: PA7
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC4
+control: pid
+pid_Kp: 71.867
+pid_Ki: 1.536
+pid_Kd: 840.843
+min_temp: 0
+max_temp: 100 # Set to 110 for S1 Pro
+
+[heater_fan hotend_fan]
+pin: PC0
+
+[fan]
+pin: PA0
+
+[mcu]
+serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
+restart_method: command
+
+[printer]
+kinematics: cartesian
+max_velocity: 300
+max_accel: 2000
+max_z_velocity: 5
+max_z_accel: 100
+
+[bltouch]
+sensor_pin: ^PC14
+control_pin: PC13
+x_offset: -31.8
+y_offset: -40.5
+z_offset: 0
+probe_with_touch_mode: true
+stow_on_each_sample: false
+
+[bed_mesh]
+speed: 120
+mesh_min: 10, 10
+mesh_max: 200, 194
+probe_count: 4,4
+algorithm: bicubic
+
+[safe_z_home]
+home_xy_position: 147, 154
+speed: 75
+z_hop: 10
+z_hop_speed: 5
+
+[filament_switch_sensor e0_sensor]
+switch_pin: !PC15
+pause_on_runout: true
+runout_gcode: PAUSE
+
+[pause_resume]
+recover_velocity: 25
+
+[bed_screws]
+screw1: 20, 29
+screw2: 195, 29
+screw3: 195, 198
+screw4: 20, 198