home-manager/linux/programs/hyprland.nix

@@ -234,7 +234,7 @@ in with lib; {
         windowrulev2 = center,class:^(.blueman-manager-wrapped)$
 
         # firefox Picture-in-Picture
-        # windowrulev2 = nofullscreenrequest,class:^(firefox-beta)$,title:^(Picture-in-Picture)$
+        windowrulev2 = nofullscreenrequest,class:^(firefox-beta)$,title:^(Picture-in-Picture)$
         windowrulev2 = float,class:^(firefox-beta)$,title:^(Picture-in-Picture)$
         windowrulev2 = pin,class:^(firefox-beta)$,title:^(Picture-in-Picture)$
 

machines/universe/configuration.nix

@@ -73,7 +73,6 @@
   services.klipper = {
     package = inputs.nixpkgs-unstable.legacyPackages.${pkgs.system}.klipper;
     enable = true;
-    configFile = ./klipper/printer.cfg;
   };
   services.moonraker = { enable = true; };
   services.mainsail = {

machines/universe/klipper/printer.cfg

@@ -1,136 +0,0 @@
-# This file contains pin mappings for the stock 2021 Creality Ender 3
-# S1 & S1 Pro. To use this config, check the STM32 Chip on the
-# Mainboard, during "make menuconfig" select accordingly either the
-# STM32F103 with "28KiB bootloader" or the STM32F401 with
-# "64KiB bootloader" and serial (on USART1 PA10/PA9) for both.
-
-# For a direct serial connection, in "make menuconfig" select
-# "Enable extra low-level configuration options" and  Serial
-# (on USART2 PA3/PA2), which is on the 10 pin IDC cable used
-# for the LCD module as follows: 3: Tx, 4: Rx, 9: GND, 10: VCC
-
-# Flash this firmware by copying "out/klipper.bin" to a SD card and
-# turning on the printer with the card inserted. The filename
-# must be changed to "firmware.bin"
-
-# With STM32F401, you might need to put "firmware.bin" in a
-# folder on the SD card called "STM32F4_UPDATE" in order to flash.
-
-# See docs/Config_Reference.md for a description of parameters.
-
-[stepper_x]
-step_pin: PC2
-dir_pin: PB9
-enable_pin: !PC3
-microsteps: 16
-rotation_distance: 40
-endstop_pin: !PA5
-position_endstop: -10
-position_max: 235
-position_min: -15
-homing_speed: 50
-
-[stepper_y]
-step_pin: PB8
-dir_pin: PB7
-enable_pin: !PC3
-microsteps: 16
-rotation_distance: 40
-endstop_pin: !PA6
-position_endstop: -8
-position_max: 238
-position_min: -13
-homing_speed: 50
-
-[stepper_z]
-step_pin: PB6
-dir_pin: !PB5
-enable_pin: !PC3
-microsteps: 16
-rotation_distance: 8
-endstop_pin: probe:z_virtual_endstop
-position_max: 270
-position_min: -4
-
-[extruder]
-step_pin: PB4
-dir_pin: PB3
-enable_pin: !PC3
-microsteps: 16
-gear_ratio: 42:12
-rotation_distance: 26.359
-nozzle_diameter: 0.400
-filament_diameter: 1.750
-heater_pin: PA1
-sensor_type: EPCOS 100K B57560G104F
-sensor_pin: PC5
-control: pid
-pid_Kp: 23.561
-pid_Ki: 1.208
-pid_Kd: 114.859
-min_temp: 0
-max_temp: 260 # Set to 300 for S1 Pro
-
-[heater_bed]
-heater_pin: PA7
-sensor_type: EPCOS 100K B57560G104F
-sensor_pin: PC4
-control: pid
-pid_Kp: 71.867
-pid_Ki: 1.536
-pid_Kd: 840.843
-min_temp: 0
-max_temp: 100 # Set to 110 for S1 Pro
-
-[heater_fan hotend_fan]
-pin: PC0
-
-[fan]
-pin: PA0
-
-[mcu]
-serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
-restart_method: command
-
-[printer]
-kinematics: cartesian
-max_velocity: 300
-max_accel: 2000
-max_z_velocity: 5
-max_z_accel: 100
-
-[bltouch]
-sensor_pin: ^PC14
-control_pin: PC13
-x_offset: -31.8
-y_offset: -40.5
-z_offset: 0
-probe_with_touch_mode: true
-stow_on_each_sample: false
-
-[bed_mesh]
-speed: 120
-mesh_min: 10, 10
-mesh_max: 200, 194
-probe_count: 4,4
-algorithm: bicubic
-
-[safe_z_home]
-home_xy_position: 147, 154
-speed: 75
-z_hop: 10
-z_hop_speed: 5
-
-[filament_switch_sensor e0_sensor]
-switch_pin: !PC15
-pause_on_runout: true
-runout_gcode: PAUSE
-
-[pause_resume]
-recover_velocity: 25
-
-[bed_screws]
-screw1: 20, 29
-screw2: 195, 29
-screw3: 195, 198
-screw4: 20, 198